FLUKE - 87 V digital multimeter DC and AC voltage 1,000 volts

Execution

Unique function for accurate voltage and frequency measurements on speed-controlled motor drives where harmonics overlap the base frequency
Display with large digits and bright two-level backlighting
True RMS measurement of voltage and current for precise measurements of non-sine wave signals
Selectable filter for voltage and frequency measurements on motor drives
Basic accuracy of 0.05 % for DC voltage
6,000 digits, 3 3/4 places
4 1/2 places for precise measurements (20,000 digits)
Thermometer (including TC probe)
Resistance measurement, continuity and diode test
10,000 µF capacitance range for components such as motor capacitors
- Min./max./average value capture with min./max. alert for automatic detection of deviations
- Peak detection for determining short-term transients up to 250 µs
- Relative value mode eliminates interference from measurement leads for low-impedance measurements
- Automatic/manual range selection for maximum flexibility
- Touch Hold captures stable readings without influence by interfering signals
- Analogue bar graph display for fast signal changes or unstable signals
- Input Alert beeps if the input sockets are connected incorrectly
- Switch-off to extend battery life
- Battery compartment for fast battery change without damaging the calibration seal
- Removable holster, holder for measurement leads and measuring tips
- Lifetime warranty

Delivery
Measuring leads
Alligator clips
Yellow holster
Temperature probe
9 V battery (installed)
CD-ROM (user manual, technical information and operating instructions)

Notes
For replacement batteries, see art. no. 1039900 405.

Brand: FLUKE
Measuring accuracy: +/- 0.5 %
Min./max. test voltage (DC): 10 µV-1000 V
Min./max. test voltage (AC): 0.1 mV-1000 V
Min./max. alternating current of measuring range: 0.1 µA-10 A
Min./max. direct current of measuring range: 0.01 µA-10 A
Continuity testing: Yes
Diode testing: Yes
Min./max. electrical-resistance measuring range: 0.1 Ohm-50 MOhm
Min./max. frequency: 0.00001 / 200 kHz
Min./max. temperature measuring range: -200 to 1090 °C
Overvoltage protection category: CAT III/1000 V | CAT IV/600 V
Length x width x height: 201 x 98 x 52 mm
Display: 6000 digits
EN standard: 61010-1 (VDE 0411-1)
Height: 52 mm
Length: 201 mm
Max. direct current of measuring range: 10 A
Max. frequency: 200 kHz
Min. direct current of measuring range: 0,01 µA
Min. frequency: 0,01 Hz
Width: 98 mm
Max. alternating current of measuring range: 10 A
Max. capacitor capacity: 9999 µF
Max. test voltage (AC): 1000 V
Max. test voltage (DC): 1000 V
Min. alternating current of measuring range: 0,1 µA
Min. capacitor capacity: 0,01 nF
Min. test voltage (AC): 0,1 mV
Min. test voltage (DC): 10 µV

87 V digital multimeter DC and AC voltage 1,000 volts

87 V digital multimeter DC and AC voltage 1,000 volts

Description

Technical data

More details

No workshop should be without it:

ErgoStrip universal stripping tool 0.2-4.0 mm length 135 mm right-handed

ATORN twist drill bit set N HSS TIN head DIN 338 1.0-10.0 mm in assortment case

ATORN A-Mech 3 assembly glove, size 9

Multifunction spray WD-40 400 ml

Lamella flap disc LSZ-F Vision zirconia alumina grain 60 dia. 125 mm

ATORN countersink set, 90°, HSS, extremely unequal pitch 6.3-20.5mm, 3-flat shnk

ATORN centre drill set HSSE TiN form A, D=1-1.6-2-2.5-3.15-4-5

Industrial atomiser type R36.501 with 360° suction system

Pneumatic special oil 100 ml silicone-free with locking cap

Adapter set 958/7

3D art. meas. stand with central clamping and micro fine adj., height 390 mm

Pliers set, 3 pcs Combination pliers, snipe nose pliers, side cutters

Protective vice jaw set 125 mm 8 pieces in bag

Safety goggles MAX A1 lens clear

ATORN A-Shield 1 cut protection glove, size 9

Lamella flap disc Z SG POWER STEELOX, dia. 125 mm, alumina zirconia, 40 grit

ATORN A-Mech 2 assembly glove, size 9

ATORN twist drill bit set STEP DRILL type N HSS vaporised 1-13 mm 0.5 and CHD

WERA torque screwdriver T 6 set to 0.6 Nm, fixed blade

Pliers wrench 250 mm up to AF 52 mm 19x position box joint

ATORN cutter blade with 18-mm snap-off blade, metal housing, with slide

ATORN connector set, 3 pieces, square output

ATORN A-View 4 safety glasses

Spiralbohrer-Satz Sprint Master 19tlg. DIN 338 HSS Ø 1,0-10,0 mm in Kassette

ATORN vernier calipers IP67 electr. 150 mm depth gauge flat

ATORN disposable ear plugs, 200 pairs

ATORN reusable corded ear plugs

KNIPEX precision circlip pliers set, 8 pieces in box

ATORN hexagonal Allen key set, 9 pieces, 1.5–10 mm, ball head, colourful

ATORN ret. ring pliers set, 8 pcs A1,A2,A11,A21,J1,J2,J11,J21 in roll-up pouch

Set of flat hand engineer's files with handle, 5 pieces, L=200mm, German cut 2

ATORN A-View 3 safety glasses

HHW twist drill bit set DIN 338 HSS type N dia. 1-13.0 mm in box

ATORN corundum abrasive fabric roll (AO) in tear-off box G180 40 mm x 50 m

Pneumatic hose reel hose dia. 13 mm, hose length 15 m max. 20 bar

ATORN twist drill bit set STEP DRILL type N HSS TiN head 1-13 mm 0.5 and CHD

ATORN ear plug dispenser

ATORN twist drill bit set N HSS TiN head DIN 338 1.0-13.0 mm 0.5 in box

T-handle 416 RA T-handle Rapidaptor

Octagonal pin punch set 6 pieces dia. 2-8 mm in stand

Inspektionskamera VideoPocket HD

ATORN A-View 2 safety glasses

Twist drill bit set HSS-E Co5 1-10 mm 0.5 mm incremental 19 pieces

ATORN measuring and clamping vee blocks 80 mm w switch magnet, wooden case

ATORN A-Shield 2 cut protection glove, size 9

ATORN steel cutting disc 125x1 mm

ATORN analogue scriber 600 mm with fine adjustment

ATORN PZ screwdriver set, 3 pcs, PZ 1-3, round blade

ATORN countersink set 90° HSS, extremely unequal pitch 6.3-20.5 mm

Free-hand cutting disc, straight, universal line PSF STEELOX grit 60 125x1.0 mm

Pneumatic metered blow gun 37 A 90 mm pipe POM Rc 1/4 grommet LW 6

ATORN 6-piece measuring instrument set, wooden case, digital vernier callipers

Prec. countersink set 5 pcs HSS-E Alunit d. 6.3/10.4/16.5/20.5/25.0 mm

ATORN cross-peen hammer 1,000 g, hickory handle, nylon handle protect. sleeve

ATORN HSSE machine tap set M3-12 HSSE DL

T-handle 411 A RA T-handle

ATORN micrometer 0-25 mm, in case

Measuring cup set 3 pcs 0.5 l, 1.0 l, 2.0 l, transparent, coloured/raised scale

Safety goggles MAX T7 lens clear

Safety goggles MAX C4 lens clear

ATORN LED magnifying lamp, 5 dioptres, 2-stage segment switching, 2.25x

ATORN countersink set, 90°, unequal spiral pitch 6.3-25.0 mm, 3-flat shank

Prec. cntrsink drill set 5 pcs dia. 6.3/10.4/16.5/20.5/25.0 mm w/ 3 clamp surf.

ATORN VDE screwdriver set, 3 pcs, cross head PH 1-3

ATORN HSSE machine tap set M3-12 HSSE GL

ATORN A-Shield 4 cut protection glove, size 9

ATORN A-Mech 1 assembly glove, size 9

ATORN twist drill bit set STEP DRILL type N HSSE purple 1-10.5 mm 0.5 and CHD

Hexagon screwdriver set 8 pieces 2-10 mm

ATORN quick-change bit holder, 1/4 inch x 60 mm

ATORN banded ear plugs, 32 dB

ATORN twist drill bit set STEP DRILL type N HSS TiN head 1-10.5 mm 0.5 and CHD

Twist drill bit set HSS-E Co5 1-13 mm 0.5 mm incremental 25 pieces

ATORN screwdriver set in workshop stand, 7 pieces